Exactly how to Install a Tub (Step By Step).
Exactly how to Install a Tub (Step By Step).
Blog Article
Right here in the next paragraph you can locate a lot of professional ideas all about How to Install a Bathtub Yourself.
:max_bytes(150000):strip_icc()/installing-a-tub-or-shower-surround-2718986-01-b02d6683a8ee4621bf9b9ac7ab0b1dd2.jpg)
Installing a bathtub isn't precisely brain surgery, yet it does require solid plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old tub with a new one is also a moderately difficult project. If the old tub is readily available, the project can move quickly; if you have to open a wall to remove the old tub and place the brand-new bath tub, the job is a lot harder. In either instance, the job is within a house handyman's skills, although you will need a helper to move out the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and fit trying it. As opposed to employing a specialist to take over a halfway-completed project, it is far better to think about utilizing one before you begin. Opportunities are you might require an expert plumber to make tube connections.
This article will certainly aid you mount a brand-new tub in your bathroom if you have actually currently gotten a new tub and also do not need to change the setup of your previous water system pipes.
Your tools and also product list need to make up the following:
Removing Old Taps
If you require to change old taps with new ones as a part of your installation, after that the first thing you must do is detach the supply of water. After doing so, turn on the faucets to drain pipes any water continuing to be in the system. The procedure of eliminating the existing taps can be quite problematic due to the limited accessibility that is commonly the situation.
Utilize a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipes to the faucets. Have a towel prepared for the staying water that will originate from the pipelines. When the supply pipes have actually been gotten rid of, utilize the same device to loosen up the nut that holds the taps onto the bath/basin. You will require to stop the solitary faucets from turning throughout this process. As soon as the faucets have been gotten rid of, the holes in the bath/basin will need to be cleaned up of any old securing compound.
Before going on to fit the new faucets, compare the pipeline links on the old taps to the brand-new taps. If the old faucets are longer than the new faucets, then a shank adapter is needed for the new faucets to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly need a plastic port to prevent damages to the thread. One end of the port fits on the plastic tail of the faucet as well as the various other end offers a link to the existing supply pipelines.
If you need to fit a monobloc, after that you will need reducing couplers, which links the 10mm pipeline of the monobloc to the conventional 15mm supply pipeline.
Next, place the tap in the installing opening in the bath/basin guaranteeing that the washing machines are in location in between the tap and also the sink. Secure the tap in position with the manufacturer supplied backnut. Once the tap is safely in position, the supply pipelines can be connected to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular tap ports. The previous type must be attached to the tap ends initially, tightening up only by hand. The supply pipes can later on be connected to the other end. Tighten up both ends with a spanner after both ends have actually been connected.
Setting up the Bath tub
Making use of the two wooden boards under its feet, position the bath tub in the required setting. The wood boards are handy in evenly spreading the weight of the bath tub over the location of the boards instead of focusing all the weight onto 4 tiny factors.
The next goal is to guarantee that the tub is leveled all round. This can be accomplished by inspecting the level and also readjusting the feet on the bath tub till the level reviews degree.
To mount faucets, fit all-time low of the outermost adaptable faucet adapter to the ideal supply pipeline by making a compression sign up with; after that do the very same for the various other faucet.
Activate the water and also examine all joints and also brand-new pipework for leakages as well as tighten them if needed. Fill up the tub and likewise check the overflow outlet and the normal electrical outlet for leakages.
Ultimately, take care of the bathroom paneling as defined in the maker's user's manual. Tiling as well as sealing around the bathtub should wait till the bath tub has actually been utilized a minimum of once as this will resolve it right into its last position.
Planning for the Setup
First of all, the supporting frame provided with the bathroom ought to be fitted (if required) according to the manufacturer's guidelines. Next off, fit the taps or mixer to the tub. When suitable the tap block, it is important to see to it that if the faucet includes a plastic washer, it is fitted between the bathroom and also the faucets. On a plastic bath, it is also sensible to fit a sustaining plate under the faucets system to avoid strain on the bath tub.
Fit the versatile tap adapters to the bottom of both taps making use of 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut supplied by the supplier to fit the plug-hole. Take a look at the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the flexible overflow pipeline to the overflow outlet. After that, screw the pipeline to the overflow face which must be fitted inside the bath. See to it you utilize all of the provided washers.
Connect the catch to the bottom of the waste outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, and also screw on the catch to the outlet. Attach the bottom of the overflow tube in a similar manner.The bathroom need to now be ready to be suited its final placement.
Tiling Around the Tub
In the location where the bathroom meets the floor tile, it is required to secure the joins with a silicone rubber caulking. This is important as the installation can move enough to fracture a rigid seal, creating the water to penetrate the wall surface in between the bath and also the tiling, leading to issues with dampness as well as feasible leaks to the ceiling listed below.
You can pick from a variety of coloured sealers to assimilate your fixtures as well as fittings. They are sold in tubes and also cartridges, and are capable of securing gaps as much as a size of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with twists of soaked paper or soft rope. Remember to always fill up the bath tub with water before sealing, to permit the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this movement before securing.
Conversely, ceramic coving or quadrant floor tiles can be used to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing waterproof or water-proof glue and grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
Hopefully you enjoyed reading our article on Installing A Bathtub. Thank you for taking a few minutes to read through our posting. Enjoyed our review? Please share it. Help another person find it. Thanks a lot for your time. Please check up our website back soon.
Check It Out Report this page